Betomix-ITH Crystal Producing Concrete Waterproofing Admixture

BETOMIX-ITH® is a gray, dry and one-component powder mixture containing white residues. BETOMIX-ITH®, consisting of cement and active chemical components, is added during the mixing of the concrete.

BETOMIX-ITH® is a waterproofing material that produces crystals by penetrating the concrete against moisture after it is mixed into the concrete as an additive.
The active chemicals in its content penetrate the surface, react to moisture and hardened concrete components and enter into a catalytic reaction.

This reaction creates insoluble crystal formation in both the cavities and capillary channels and cracks of the concrete, rendering the concrete permanently impermeable to water.
It does not allow water and other liquids to leak from any direction, even under high hydrostatic pressure.

Purpose of usage

BETOMIX-ITH® increases the water impermeability, frost resistance and strength of concrete structures by filling the pores with crystal particles.
BETOMIX-ITH® is added during the mixing of the concrete. Water-soluble chemicals are evenly distributed in the concrete mix.
The active ingredients of the BETOMIX-ITH® additive ensure the crystallization of insoluble hydrates in the pores on the concrete. Pinhead crystals fill the voids, fine cracks and holes in the concrete.

The crystal formation process continues only when it is in contact with water and moisture until the cavities are completely closed. In this way, a strong and durable interlocking crystal network is formed. This prevents water from penetrating into the concrete, creating a strong and continuous waterproofing effect.

After using BETOMIX-ITH® additive, no additional waterproofing is required. Compatible with other additives for concrete mix (plasticization, frost resistance, etc.)

Technical Features and Advantages

  • It is resistant to 14 Bar high hydrostatic pressure. It does not lose its waterproofing properties under high hydrostatic pressure.
  • It closes hairline cracks and capillary gaps up to 0.4 – 0.5mm in concrete. Complete insulation is provided after these cracks are closed with crystal.
  • In case of mechanical damage or any other reason water enters the concrete, it heals the concrete by self-repairing by producing crystals again.
  • It provides diffusion transition property in the concretes it is applied to. Thanks to this feature, the moisture in the concrete evaporates between the
  • Crystal cavities and allows the wall to dry.
  • It eliminates the disadvantages of superficial insulation materials by using instead of cover type materials.
  • Freezing of concrete is prevented and tensile strength increases.
  • It integrates with the concrete it is applied to and provides complete impermeability throughout the life of the concrete.
  • It protects the iron in concrete from corrosion.
  • It is non-toxic and can be used in drinking water tanks and facilities.
  • It allows the concrete to breathe.
  • It is resistant to aggressive chemicals. (pH=3-14), It prevents the formation of ettringite in concrete.
  • Does not require dry ground.
  • The edges of the concrete structure will not be punctured, torn or broken.
  • It does not require cost-increasing priming or correction on the surface before application.
  • It does not require sealing, finishing or finishing the entire surface at corner and edge joints or between cladding.
  • It can be applied to previously treated or new concretes.
  • It does not require infill or shielding in the insertion of steel, mesh wire or other materials.
  • It is reactive in its current state, it becomes active every time it comes into contact with water.
  • Containing concrete from sea water, waste water, oil, etc. Protects from chemicals such as
  • Its application is less costly than other methods.
  • There is no deterioration in the crystal structure. It is permanent and permanent.
  • It can be easily added to the concrete at the plant or at the construction site.
  • It minimizes cracks and shrinkage in concrete.
  • It is easy to apply.

Usage Areas

  • Curtain concretes
  • Concrete block foundations
  • Dams
  • Industrial buildings
  • Reinforced concrete structures
  • Roofs and balconies
  • Water storage tanks
  • Elevator shafts
  • Tunnels, underpasses

 

  • Construction joints
  • Multi-storey car parks
  • Concrete Roads
  • Waste water plants
  • Docks and piers
  • Simming pools
  • Underground parks
  • Concrete channels
  • Bridges

Consumption

It is used up to 1.0% dry admixture of cement mass in the concrete mixture or 4 kg for 1 cubic meter of concrete.

Operating Instructions

  • To mix up

Clean mains water is added until “BETOMIX-ITH” reaches a boza consistency and mixed with a paint mixer at low speed for 2 minutes until it reaches a homogeneous consistency.

The resulting mixture should be used within 5 minutes. Keep mixing constantly as you apply. If the mixture starts to harden, add very little water.

If it is added to the concrete mixer (transmixer), it is mixed for 10 minutes and poured. Please pour the concrete mix in accordance with the concrete usage rules.

BETOMIX-ITH should be added to the concrete during mixing. “BETOMIX-ITH” should form a homogeneous mixture with concrete.

  • Compatibility:

It is frost resistant, suitable for use with plasticizers and other additives.

  • Warning/ Restriction:

BETOMIX-ITH® is only effective when used with mineral materials containing cement. When applied to microsilica-containing and polymer concretes, efficient results are not obtained. It should not be used in gypsum and lime mortars.

Application

BETOMIX-ITH® Concrete mixer, which is brought to the consistency of boza by mixing with water, is mixed slowly while it is in operation and is waited for 10 minutes, and the additive is homogeneously mixed into the concrete mortar. Then the concrete casting process is carried out.

Other

  • Color : Gray.
  • Packaging : In 5 and 10 Kg PP buckets.
  • Shelf Life : It is suitable for use for 18 months from the production date if stored in original, unopened and undamaged packages in a dry environment.
  • Storage and Transportation Conditions : It can be stored and transported in a dry and cool environment under weather conditions between -50ºC and +50ºC.

Health and Safety

“BETOMIX-ITH” is non-toxic and does not pose a danger to the environment and human health during transportation, storage and application. According to GOST 12.1.007-76, it belongs to the 4th hazard class in terms of physico-chemical and sanitary-biological properties (less dangerous substances – the maximum level of pollution is 50 mg / m³). Use appropriate safety glasses, rubber gloves and mask while using this product. In case of contact with eyes and skin, rinse immediately with plenty of water and seek medical advice.